Cisco交换机综合实例(二)

王朝other·作者佚名 2008-05-19

宽屏版字体: 小|中|大|超大

3. Catalyst 4003 的配置

下面给出Catalyst 4003 的配置清单

Enter password:

Console enable

Enter password:

Console (enable) set system name 4003-ER-F1

System name set.

4003-ER-F1 (enable) set system location 1st Floor Equipment Room

System location set.

4003-ER-F1 (enable) set system contact sysadmin@bigcorp.com

System contact set.

4003-ER-F1 (enable) set time 04/30/1999 9:45:00

Fri Apr 30 1999, 09:45:00

4003-ER-F1 (enable) set password

Enter old password:

Enter new password:

Retype new password:

Password changed.

4003-ER-F1 (enable) set enablepass

Enter old password:

Enter new password:

Retype new password:

Password changed.

4003-ER-F1 (enable) set banner motd %

4003-ER-F1 (Catalyst 4003)

Access Restricted

MOTD banner set

4003-ER-F1 (enable) set interface sc0 10.10.1.20/24

Interface sc0 IP address set.

4003-ER-F1 (enable) set ip route default 10.10.1.1

Route added.

4003-ER-F1 (enable) set ip dns server 10.10.10.100

10.10.10.100 added to DNS server table as primary server.

4003-ER-F1 (enable) set ip dns domain bigcorp.com

Default DNS domain name set to bigcorp.com

4003-ER-F1 (enable) set ip dns enable

DNS is enabled

4003-ER-F1 (enable) set vtp domain BigCorp mode client

VTP domain BigCorp modified

4003-ER-F1 (enable) set module name 1 Supervisor

Module name set.

4003-ER-F1 (enable) set module name 2 Gig Uplinks

Module name set.

4003-ER-F1 (enable) set port flowcontrol 2/1-2 send off

Ports 2/1-2 flow control send administration status set to off

(ports will not send flowcontrol to far end)

4003-ER-F1 (enable) set port flowcontrol 2/1-2 receive off

Ports 2/1-2 flow control receive administration status set to off

(ports will not allow far end to send flowcontrol)

4003-ER-F1 (enable) set port negotiation 2/1-2 enable

Ports 2/1-2 negotiation enabled

4003-ER-F1 (enable) set port name 2/1-2 GEC 802.1Q Trunk

Ports 2/1-2 name set.

4003-ER-F1 (enable) set port channel 2/1-2 desirable

Port(s) 2/1-2 channel mode set to desirable.

4003-ER-F1 (enable) set trunk 2/1 desirable dot1q

Port(s) 2/1-2 trunk mode set to desirable.

Port(s) 2/1-2 trunk type set to dot1q.

4003-ER-F1 (enable) set module name 3 Gig Server Links

Module name set.

4003-ER-F1 (enable) set port name 3/1-2 Corporate Server

Ports 3/1-2 name set.

4003-ER-F1 (enable) set port name 3/3 DevEng Server

Port 3/3 name set.

4003-ER-F1 (enable) set port name 3/4 QA Server

Port 3/4 name set.

4003-ER-F1 (enable) set port flowcontrol 3/1-4 send desired

Ports 3/1-4 flow control send administration status set to desired

(ports will send flowcontrol to far end if far end supports it)

4003-ER-F1 (enable) set port flowcontrol 3/1-4 receive desired

Ports 3/1-4 flow control receive administration status set to desired

(ports will allow far end to send flowcontrol if far end supports it)

4003-ER-F1 (enable) set port channel 3/1-2 off

Port(s) 3/1-2 channel mode set to off.

4003-ER-F1 (enable) set port channel 3/3-4 off

Port(s) 3/3-4 channel mode set to off.

4003-ER-F1 (enable) set trunk 3/1-4 off

Port(s) 3/1-4 trunk mode set to off.

4003-ER-F1 (enable) set spantree portfast 3/1-4 enable

Warning: Spantree port fast start should only be enabled on ports connected

to a single host. Connecting hubs, concentrators, switches, bridges, etc. to

a fast start port can cause temporary spanning tree loops. Use with caution.

Spantree ports 3/1-4 fast start enabled.

4003-ER-F1 (enable) set vlan 10 3/1-2

VLAN 10 modified.

VLAN 1 modified.

VLAN Mod/Ports

---- -----------------------

10 2/1-2

3/1-2

4003-ER-F1 (enable) set vlan 20 3/3

VLAN 20 modified.

VLAN 1 modified.

VLAN Mod/Ports

---- -----------------------

20 2/1-2

3/3

4003-ER-F1 (enable) set vlan 40 3/4

VLAN 40 modified.

VLAN 1 modified.

VLAN Mod/Ports

---- -----------------------

40 2/1-2

3/4

4003-ER-F1 (enable)

4. RSM 的配置

对于RSM模块的命令与Cisco的路由器相似

下面给出配置清单

5509-ER-F1 (enable) session 3

Trying Router-3...

Connected to Router-3.

Escape character is '^]'.

Routerenable

Router#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#hostname RSM-ER-F1

RSM-ER-F1(config)#enable password extra_secret_word

RSM-ER-F1(config)#line vty 0 6

RSM-ER-F1(config-line)#password secret_word

RSM-ER-F1(config-line)#ip domain-name bigcorp.com

RSM-ER-F1(config)#ip name-server 10.10.10.100

RSM-ER-F1(config)#ip domain-lookup

RSM-ER-F1(config)#interface vlan 1

RSM-ER-F1(config-if)#description default (vlan1) VLAN interface

RSM-ER-F1(config-if)#ip address 10.10.1.1 255.255.255.0