Cisco6000MSFC口令的恢复

王朝other·作者佚名 2008-05-19

Contents

Description

Step-by-Step Procedure

Example of a Password Recovery on the Catalyst 6000 MSFC Module

Related Information

Description

This document describes the password recovery procedure for the Cisco Catalyst 6000 Multilayer Switch Feature Card (MSFC).

Step-by-Step Procedure

Attach a terminal or PC with terminal emulation to the console port of the switch.

Use the following terminal settings: 9600 baud, no parity, 8 data bits, 1 stop bit

Type show module to determine the MSFC card on which to do password recovery.

The MSFC module is in slot 15 or 16.

Reset the MSFC module you want to do password recovery on.

Use the reset command to do this.

Wait 5 seconds and then connect to the MSFC console using the switch console command.

After seeing the message "Connected to Router", issue a break sequence.

The break key is a unique sequence that will break the MSFC into rommon. If this does not work, please refer to the break sequence page.

The MSFC will boot to a rommon prompt.

Type confreg 0x42 at the rommon prompt to configure the MSFC to boot without its configuration.

Display the current software in bootflash by issuing the dir bootflash: command and record the current software version.

Boot the system with the boot bootflash: command.

NOTE : Do NOT boot the system using the c6msfc-boot image. Doing so will result in loss of configuration after the password recovery process.

After the system boots, answer "No" to all the set-up questions or press Ctrl-C to skip the initial set-up procedure.

Type enable at the Router prompt. This will put you in enable mode and you will see the Router# prompt.

Type config mem or copy startup-config running-config to copy the nonvolatile RAM (NVRAM) into memory.

This is a crucial step. DO NOT save the configuration (do not use write term or copy running-config startup-config)

Type write terminal or show running-config.

At this point, you should see the full configuration with the unknown enable password or enable secret. All other interfaces are shut down.

Type configure terminal to make the necessary changes.

The prompt is now hostname(config)#

Type enable secret . Replace with your password.

Use the no shutdown command on interfaces that are being used.

If you use the show ip interface brief command, every interface that you want to use should be up.

Type config-register 0x2102

Press Ctrl-Z to leave the configuration mode. The prompt is now hostname#

Type write memory or copy running-config startup-confi

g to commit the changes.

Example of a Password Recovery on the Catalyst 6000 MSFC Module

switch (enable) show module

Mod Slot Ports Module-Type

Model

Status

--- ---- ----- ------------------------- ------------------- --------

1000BaseX Supervisor

WS-X6K-SUP1A-2GE

Multilayer Switch Feature WS-F6K-MSFC

10/100BaseTX Ethernet

WS-X6248-RJ-45

1000BaseX Ethernet

WS-X6408-GBIC

MM OC-12 ATM

WS-X6101-OC12-MMF

Mod Module-Name

Serial-Num

--- ------------------- -----------

SAD03423133

SAD03414563

SAD03242737

SAD03220152

SAD03433465

Mod MAC-Address(es)

--- -------------------------------------- ------ ---------- -----------------

00-30-96-2a-2a-9e to 00-30-96-2a-2a-9f 1.0

5.2(1)

5.4(3)

00-30-96-2a-2a-9c to 00-30-96-2a-2a-9d

00-50-3e-9f-20-00 to 00-50-3e-9f-23-ff

00-30-96-2a-2a-a0 to 00-30-96-2a-2a-df 1.2

12.1(1)E,

00-50-f0-af-24-d0 to 00-50-f0-af-24-ff 1.1

4.2(0.24)V 5.4(3)

00-d0-58-e9-d0-f0 to 00-d0-58-e9-d0-f7 2.1

4.2(0.24)V 5.4(3)

00-d0-bc-ef-03-68 to 00-d0

-bc-ef-03-87 1.0

12.0(5)XS, 12.0(5)XS,

Mod Sub-Type

Sub-Model

Sub-Serial

Sub-Hw

--- ----------------------- ------------------- ----------- ------

L3 Switching Engine

WS-F6K-PFC

SAD03424837 1.0

switch(enable) reset 15

Unsaved configuration on module 15 will be lost

Do you want to continue (y/n) [n]? y

2000 Jun 23 06:36:59 %SYS-5-MOD_RESET:Module 15 reset from Console//

Resetting module 15...

switch(enable) switch console

Trying Router-15...

Connected to Router-15.

Type ^C^C^C to switch back...

(A break-sequence has been sent here)

monitor: command "boot" aborted due to user interrupt

rommon 1 confreg 0x42

You must reset or power cycle for new config to take effect

rommon 2 dir bootflash:

File size

Checksum

File name

1606784 bytes (0x188480)

0xe58d8560

c6msfc-boot-mz.120-7.XE1

8998276 bytes (0x894d84)

0x1476de9

c6msfc-jsv-mz.121-1.E.bin

rommon 3 boot bootflash:c6msfc-jsv-mz.121-1.E.bin

Self decompressing the image : ########################################################################

#######################################################################################################

############ [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

Rights clause at FAR sec. 52.227-19 and subparagraph

Software clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc.

170 West Tasman Drive

&nb

sp;

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) MSFC Software (C6MSFC-JSV-M), Version 12.1(1)E, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

Compiled Fri 24-Mar-00 13:57 by kpma

Image text-base: 0x60008900, data-base: 0x6146A000

Cisco Cat6k-MSFC (R5000) processor with 57344K/8192K bytes of memory.

Processor board ID SAD03414563

R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache

Last reset from power-on

Bridging software.

X.25 software, Version 3.0.0.

TN3270 Emulation software.

123K bytes of non-volatile configuration memory.

4096K bytes of packet SRAM memory.

16384K bytes of Flash internal SIMM (Sector size 256K).